How To Install An Electric Bike Hub Motor Kit – Phoenix II Conversion Kit

How To Install An Electric Bike Hub Motor Kit – Phoenix II Conversion Kit



Provided by www.electricrider.com, home of the 50mph Phoenix Paratrooper Electric Bike!

A quick, basic guide to installing an electric bike conversion kit, or more specifically, the Phoenix II hub motor kit. “Most” ebike conversion kits will be installed in a similar fashion, so we hope this helps make your DIY electric bike project a success!

source

21 Comments
  • Chris Hvid
    Posted at 07:12h, 22 February Reply

    No torque arms. Recipe for disaster…

  • PHY ANIS
    Posted at 07:12h, 22 February Reply

    Dear brother,
    My bike is veloce outrage 604.
    How to convert ebike…????
    Please help me…

  • Friar Talk
    Posted at 07:12h, 22 February Reply

    That's a pleasant voice, I could go to sleep thinking about motorized bicycles.

  • Jesee Finley
    Posted at 07:12h, 22 February Reply

    ? can it work on a rode bick

  • dippster357
    Posted at 07:12h, 22 February Reply

    The thing I hate about this is they sell these kits but no talk of where to get the batteries and most of the time you have to build the battery yourself I don’t understand why the battery can’t already be built and in a water proof case and if your lucky enough to find it it will cost 3 x more than the wheel kit! Which you don’t find out until you buy the wheel kit.

  • Bhushan Pavan
    Posted at 07:12h, 22 February Reply

    How to assemble electric bicycle. Link http://youtu.be/ywFiZ4MZLQ0

  • Haley Hefner
    Posted at 07:12h, 22 February Reply

    I just had a few questions
    ~can you still pedal normally if you do not want to use the motor
    ~will this work with a multi gear cruiser bike?
    ~if so where can I buy this kit?

  • Carol Stevens
    Posted at 07:12h, 22 February Reply

    I heard that scientists are working to develop a human powered bicycle.
    That would be amazing.

  • Stuart
    Posted at 07:12h, 22 February Reply

    Your voice is so creepy

  • Shekar Reddy
    Posted at 07:12h, 22 February Reply

    Which wire connection goes where? How does the battery connect? pity you missed important steps.

  • Heath Brockway
    Posted at 07:12h, 22 February Reply

    Hello half, wheres Dave?

  • Bob Bigtoe
    Posted at 07:12h, 22 February Reply

    worst video. I don't need to be shown how to change an inner tube you idiots. I don't need to sit there watching u tighten a bolt. Really bad video. What a waste of time.

  • Klara Sprudel
    Posted at 07:12h, 22 February Reply

    Can I install any cassette on this hubmotor? I have 9-speed would that fit?

  • buder5
    Posted at 07:12h, 22 February Reply

    i wanted a tut about those hud without wheel

  • Rose Rodent
    Posted at 07:12h, 22 February Reply

    Hilarious! I watched the whole thing to see how to route the cables, loads of tedious stuff about taking off a tyre which is totally standard, then they skip over the cable part, he just gives a tight shot of connecting plugs then it's over.

  • HONDA cbr
    Posted at 07:12h, 22 February Reply

    is the new wheel not wider than a standard wheel not sure will it fit in any bike frame ?

  • Escorpio40
    Posted at 07:12h, 22 February Reply

    I don't like the wiring to be exposed to the elements and looks bad.

  • Francisco Sanchez
    Posted at 07:12h, 22 February Reply

    I was expecting to see the ride…

  • Russ Bowers Channel
    Posted at 07:12h, 22 February Reply

    Are there any kits that work with a 142x12mm rear axle? Thanks for the high quality instructions!

  • Mendez Campos
    Posted at 07:12h, 22 February Reply

    that tired to tight

  • REIOLO
    Posted at 07:12h, 22 February Reply

    shows how to put on a tire, and not showing how to transfer cmponent

Post A Comment

× WhatsApp